Pritzel, Christian
Preferred name
Pritzel, Christian
5 results
Now showing 1 - 5 of 5
- Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Influence of iron doped TiO<sub>2</sub> nanotubes on the hydration of tricalcium silicateEnvironmental pollution is one of biggest challenges facing the world. The promising technology to control this problem is utilization of semiconductor materials as photocatalyst. It is well known that normal TiO 2 showing photocatalytic activity in the UV light, so to decrease the band gap and shifting into visible light, titanium dioxide nanotubes was doped with Fe 3+ ions. The influence of fabricated Fe‐doped TiO 2 nanotubes (Fe/TiNTs) on the hydration of tricalcium silicate (C 3 S) have been studied. Addition of 1.0 wt%, 2.0 wt% and 3.0 wt% of Fe/TiNTs into C 3 S system significantly accelerated the course of hydration. Study on the hydration products after 8h, 1d and 7d improved the degree of hydration. The enhancing of compressive strength of hydrated C 3 S after 7d, 14d and 28d was observed comparing to the normal TiO 2 nanotubes (TiNTs). Also treating both Fe/TiNTs and TiNTs with supersaturated Ca(OH) 2 solution revealed a strong interaction between Ca 2+ ‐ ions and nanotubes particularly in the presence of iron (Fe/TiNTs). The specific surface area of hydration products in the presence of Fe/TiNTs was increased. In this study, isothermal calorimetry was utilized for the course of hydration, x‐ ray powder diffraction (XRD) for the phase composition in combination with simultaneous thermal analysis (STA) and gas adsorption (GA) for measuring specific surface area of nanotubes and hydration products.Source Type:Article3 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Nanodentistry aspects explored towards nanostructured ZrO2: Immobilizing zirconium-oxide nanotube coatings onto zirconia ceramic implant surfacesWe report on a facile strategy to impart nanostructured morphology to commercially available ceramic-preforms used for biomedical applications in the field of dentistry. This process involves the deposition of nanotubular zirconium-oxide (ZrNT) membranes onto zirconia (ZrO2) ceramic discs at ambient conditions. ZrNTs are fabricated via electrochemical anodization of zirconium foil in a one-pot synthesis. The ZrNT film is detached from the metal-foil using office-adhesive tape and freestanding ZrNT films were obtained via dissolution of adhesives in a solvent bath, which also facilitate the transfer of ZrNT film onto the ceramic. This simple technique allows to impart a robust micro-nanoscale structure to bulk-ceramics that can potentially offer insights into designing ‘smart’ implants in the field of ceramic-biomaterial applications.Source Type:Article3 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Preparation and Characterization of Transferable Encapsulated Dye-Sensitized Solar CellsThe increasing demand for sustainable energy as a means to combat the impact of climate change is addressed via a novel concept in the present work. Herein presented are developed transferable encapsulated dye-sensitized solar cells, canonically “solar capsules”, for photovoltaic applications on alternative surfaces, such as facades. The solar capsule assembly houses all the components necessary for photovoltaic energy conversion, enclosed within a semiconductor nanotubular array, making them truly unique in their construction. This capsule-style unit enables an easy transfer and draft onto a wide range of materials and surfaces for photovoltaic functionalization and applications. This type of dye-sensitized solar cell typically consists of transferred solar capsules and two additional electrodes. The design and construction of solar capsules means they have a high economic viability as they can seamlessly be up-scaled using commercially established techniques such as anodization and subsequent functionalization. This work demonstrates a working model of such transferable solar capsules by fabricating TiO2 nanotubes that are functionalized via facile dip- and spin-coating techniques in a wet lab at ambient conditions. These prototypes are characterized in bulk and are thoroughly investigated at the nanoscale for information on the chemical distribution of the constituents, as they may be influenced during the manufacturing process.Source Type:Article4 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Synthesis and Characterization of Iron-Doped TiO2 Nanotubes (Fe/TiNTs) with Photocatalytic ActivityOne of the most significant global challenges for humans is environmental pollution. The technology to control this problem is the utilization of semiconductors as photocatalysts. In the current study, iron-doped titania nanotubes (Fe/TiNTs) with increased photocatalytic effect were synthesized via a modified hydrothermal method. The products were characterized by X-ray powder diffraction, scanning electron microscopy, transmission electron microscopy (TEM), gas adsorption, electron spin resonance (ESR) and UV–Vis diffuse reflectance spectroscopy (DRS). TEM results indicated that Fe/TiNTs have a tubular and uniform structure with an average outer diameter of 23–48 nm and length of 10–15 µm. ESR and DRS revealed that Fe3+ ions were successfully introduced into the TiNT structure by replacing Ti4+ ions. An enhanced light absorption in the range of 400–600 nm additionally indicated successful doping. The band gap was narrowed as iron wt% was increased. The photocatalytic activity was evaluated by the degradation of methyl orange (MO) in the presence of Fe/TiNTs and TiTNs by monitoring the degradation of MO under UV light irradiation. An acceleration on the hydration of Portland cement was observed in the presence of 2.0 wt% Fe/TiNTs. Fe/TiNTs can be used as a nanomaterial in cement-based building materials to provide self-cleaning properties to the surface of concrete even in indoor environments.Source Type:Article7 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , The facilitated synthesis of core‐multi‐shell silica nanopArticles and its performance onto cementitious based system in comparison with commercial silica nanopArticlesThe implementation of nanopArticles in cementitious systems have been studied for long time, however the knowledge about the influence of nanosized part (e.g. silica nanopArticles) has still to be fulfilled. The enhancement of cementitious matrix, specifically in the ultra‐high‐performance‐concrete (UHPC) system, has always been focused by researchers in various means of investigation and the application of silica nanopArticle plays a significant role as one of the attempts. Different methods have been applied for synthesizing silica nanopArticles (including the core multi‐shell silica nanopArticle) within this study to simplify the process. Moreover, the comparison of two types of silica nanopArticle (synthesized and commercial) has been done in mean of character and effect to the cementitious systems by appropriate methods, to be named as: size distributions examination, microscopic methods, investigation of mechanical properties, phases composition, etc. In order to hamper crack propagation at the nanoscale, a brand‐new and simple synthesized core multi‐shell silica nanopArticle with a high specific surface area was able for the first time be applied to the scope of cementitious matrices with an impressive impact on the properties of the investigated UHPC systems. This silica nanopArticle performs double functions: as nanoscopic shock absorber and as an additive to achieve a homogeneous nanoscale elastomer distribution and thus generates positive influence not only on the properties of UHPC, but also on future solutions for materials and environmental issues. With deep and meticulous study in the future, this type of complex nanopArticle is promising great applications to give a hand to find the solution for raw materials and therefore being closer to the aim of greener construction industry.Source Type:Article4