Butz, Benjamin
4 results
Now showing 1 - 4 of 4
- Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Biosensing with a scanning planar Yagi-Uda antennaWe investigate a model bioassay in a liquid environment using a z-scanning planar Yagi-Uda antenna, focusing on the fluorescence collection enhancement of ATTO-647N dye conjugated to DNA (deoxyribonucleic acid) molecules. The antenna changes the excitation and the decay rates and, more importantly, the emission pattern of ATTO-647N, resulting in a narrow emission angle (41°) and improved collection efficiency. We efficiently detect immobilized fluorescently-labeled DNA molecules, originating from solutions with DNA concentrations down to 1 nM. In practice, this corresponds to an ensemble of fewer than 10 ATTO-647N labeled DNA molecules in the focal area. Even though we use only one type of biomolecule and one immobilization technique to establish the procedure, our method is versatile and applicable to any immobilized, dye-labeled biomolecule in a transparent solid, air, or liquid environment.Source Type:Article318 130 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , High-speed nonlinear focus-induced photoresponse in amorphous silicon photodetectors for ultrasensitive 3D imaging applicationsA large and growing number of applications benefit from simple, fast and highly sensitive 3D imaging sensors. The Focus-Induced Photoresponse (FIP) can achieve 3D sensing functionalities by simply evaluating the irradiance dependent nonlinear sensor response in defect-based materials. Since this advantage is intricately associated to a slow response, the electrical bandwidth of present FIP detectors is limited to a few kHz only. The devices presented in this work enable modulation frequencies of 700 kHz and beat frequency detection up to at least 3.8 MHz, surpassing the bandwidth of reported device architectures by more than two orders of magnitude. The sensors achieve a SNR of at least ∼53dB at 115cm and a DC FIP detection limit of 0.6 µW/mm2. The mature and scalable low-temperature a-Si:H process technology allows operating the device under ambient air conditions waiving additional back-end passivation, geometrical fill factors of 100% and tailoring the FIP towards adjustable 3D sensing applications.Source Type:Article266 242 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , HiPIMS deposition of superconducting Nb thin films onto Cu substrates(2023); ; ; ; The use of energetic condensation techniques, such as HiPIMS, has the potential to significantly improve the superconducting performance of coated Cu cavities by producing bulk-like Nb thin films. However, in order to benefit from these techniques, a deeper understanding of the effects of, and the relationship between, the different deposition parameters, the physical properties of the deposited films and the superconducting performance of the films, is still required. This contribution details the effects of different HiPIMS deposition parameters on the morphological, crystallographic and superconducting properties of Nb thin films deposited onto electropolished Cu substrates. Higher duty cycles (8 – 20 %) than previous HiPIMS investigations were used in the majority of the coatings. The films displayed more bulk-like crystallographic properties, indicated here by the lattice parameter, with a “transition zone” apparent in the early stages of film growth. A reduction in the surface roughness as well as interfacial voids, compared to typical DC MS Nb films, was also observed. The superconducting performance of the films, specifically the first magnetic flux entry field, showed a marked reliance on the substrate bias and the film thickness. Conversely, the HiPIMS duty cycle appears to have a comparatively insignificant effect. •Investigation of multiple HiPIMS coating parameters for the deposition of Nb thin films onto Cu substrates.•Predicted improved interface and surface roughness observed across all HiPIMS samples.•A morphological/crystallographic “transition zone” is observed between 1 and 2 μm film thickness.•Superconducting performance of Nb films directly linked to their crystallographic properties, i.e. lattice parameter and crystallite size.•HiPIMS duty cycle does not appear to influence the superconducting performance of Nb thin films.Source Type:Article2 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Single-photon emission from silicon-vacancy color centers in polycrystalline diamond membranesSingle-color centers in thin polycrystalline diamond membranes allow the platform to be used in integrated quantum photonics, hybrid quantum systems, and other complex functional materials. While single-crystal diamond membranes are still technologically challenging to fabricate as they cannot be grown on a non-diamond substrate, free-standing polycrystalline diamond membranes can be conveniently fabricated at large-scale from nanocrystalline diamond seeds on a substrate that can be selectively etched. However, their practical application for quantum photonics is so far limited by crystallographic defects, impurities, graphitic grain boundaries, small grain sizes, scattering loss, and strain. In this paper, we report on a single-photon source based on silicon-vacancy color centers in a polycrystalline diamond membrane. We discuss the spectroscopic approach and quantify the photon statistics, obtaining a g2(0) ≈ 0.04. Our findings hold promise for introducing polycrystalline diamond to quantum photonics and hybrid quantum systems.Source Type:Article2