Khosravani, Mohammad Reza
11 results
Now showing 1 - 10 of 11
- Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Brittle fracture of notched components fabricated by stereolithographySince additive manufacturing (AM, i.e., 3D printing) has been widely used for production of end-used products, the mechanical strength of parts fabricated by this technology have gained considerable significance. The current study presents fracture load assessment of 3D-printed components fabricated by the stereolithography (SLA) technique using UV sensitive resin material. In this context, dumbbell-shaped specimens were printed and tested to determine basic mechanical properties. Moreover, V-notched semi-circular bending test coupons with various notch opening angles (i.e., 15°, 30°, 45°, 60°, 75°, and 90°) were printed and examined. Parallel to the experimental tests, we developed a finite element model to simulate the load carrying performance of 3D-printed parts. Moreover, we used the digital image correlation technique to determine displacement and strain field on the surface of the examined specimens. Since the mechanical strength and fracture behavior of 3D-printed parts are investigated in the current study, the presented outcomes can be utilized for innovative designs of parts fabricated by SLA with a higher mechanical strength, and improved load-carrying capacity.Source Type:Article7 11 - Some of the metrics are blocked by yourconsent settings
Publication Characterization of 3D-printed PLA parts with different raster orientations and printing speedsFabrication based on additive manufacturing (AM) process from a three-dimensional (3D) model has received significant attention in the past few years. Although 3D printing was introduced for production of prototypes, it has been currently used for fabrication of end-use products. Therefore, the mechanical behavior and strength of additively manufactured parts has become of significant importance. 3D printing has been affected by different parameters during preparation, printing, and post-printing processes, which have influence on quality and behavior of the additively manufactured components. This paper discusses the effects of two printing parameters on the mechanical behavior of additively manufactured components. In detail, polylactic acid material was used to print test coupons based on fused deposition modeling process. The specimens with five different raster orientations were printed with different printing speeds. Later, a series of tensile tests was performed under static loading conditions. Based on the results, strength and stiffness of the examined specimens have been determined. Moreover, dependency of the strength and elastic modulus of 3D-printed parts on the raster orientation has been documented. In the current study, fractured specimens were visually investigated by a free-angle observation system. The experimental findings can be used for the development of computational models and next design of structural components.Source Type:Article3 10 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Digital Twin Modeling for Smart Injection MoldingIn traditional injection molding, each level of the process has its own monitoring and improvement initiatives. But in the upcoming industrial revolution, it is important to establish connections and communication among all stages, as changes in one stage might have an impact on others. To address this issue, digital twins (DTs) are introduced as virtual models that replicate the entire injection molding process. This paper focuses on the data and technology needed to build a DT model for injection molding. Each stage can have its own DT, which are integrated into a comprehensive model of the process. DTs enable the smart automation of production processes and data collection, reducing manual efforts in supervising and controlling production systems. However, implementing DTs is challenging and requires effort for conception and integration with the represented systems. To mitigate this, the current work presents a model for systematic knowledge-based engineering for the DTs of injection molding. This model includes fault detection systems, 3D printing, and system integration to automate development activities. Based on knowledge engineering, data analysis, and data mapping, the proposed DT model allows fault detection, prognostic maintenance, and predictive manufacturing.Source Type:Article1 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Effects of steps on the load bearing capacity of 3D-printed single lap jointsDamage in adhesively bonded joints typically initiates in the overlap area due to high level of bonding (peel) stress. Different approaches are being considered to decrease the peel stress and improve the overall strength of the joint. One possible approach is to shape the over lap area into a stepped form configuration and enhance the performance of the joint. In the current study, we investigate effects of stepped-shape overlap area on the load bearing capacity of additively manufactured single-lap joints. To this aim, stepped-lap adhesively bonded joints with different designs and geometries in the overlap (bonding) area are considered with 3D-printed polylactic acid (PLA) adherends using the fused deposition modeling (FDM) process. Three configurations with different step sizes are considered to manufactured a set of adhesively bonded single-lap joints and to investigate the optimum length of the steps. The results are compared with our previous experimental findings on 3D-printed conventional single-lap joints. The obtained outcomes reveal that creating steps in the overlap area has a significant influence on the structural integrity and fracture load of 3D-printed adhesive-bonded joints and the bonded structures with identical step size in boding area reveal a better performance in load carrying capacity and shows a higher fracture load. Parallel to the experimental practices, a finite element model also developed to simulate the load carrying performance of the adhesively bonded singlelap joints with equal step size and 3D-printed PLA adherends. The FE model confirms the experimental outcomes and reveals the details of the cohesive failure and damage evolution mechanism in this bonded structures with PLA printed adherends. The proposed technique has a great potential to be a competitive alternative to conventional single-lap joints made by 3D printing. The presented results can be used for further fabrication of 3D-printed joints with a better structural performance.Source Type:Article2 15 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Experimental investigations on the dynamic behavior and fracture of composite materials(2018)Various types of composites are known to have excellent and superior mechanical properties. The extremely high strength to weight ratio and the high resistance to corrosion as favorable mechanical properties, converts the composites to multifunctional structures in various applications. This thesis focuses on details of experimental investigations of fracture mechanics on two different composite materials: a sandwich composite T-joint and an ultra-high performance concrete (UHPC). The utilization of sandwich composites in aviation industry is significantly increased. In this respect, the aim of the current research is to identify the damage mechanism of sandwich composite T-joints and to obtain accurate material behavior under various loading and environmental conditions. For investigation of the sandwich composite Tjoints, series of experimental tests have been carried out in quasi-static and dynamic loading conditions and failure mechanisms are investigated. Moreover, effects of working conditions during the flight on the behavior of the sandwich composite are studied. To this end, the natural environment is simulated experimentally which influences the strength of the T-joints. This effect is determined by accelerated ageing of the honeycomb sandwich T-joints. Developments of material science as one pillar of modern technology, leads to substitute metallic materials with cementitious composites which can be counted a milestone in human living standards. Although a huge potential in application of UHPC material is given, technical information about the dynamic behavior of this material is still limited. In this dissertation, in order to study the UHPC response to the dynamic loading, series of spalling tests and dynamic Brazilian experiments have been conducted. In this regard, a linear elastic fracture mechanics-based approach is used to study the dynamic fracture and determine material properties under a high rate of loading. Parallel to the experiments, the performed tests on both mentioned composites, are numerically simulated in commercial finite element software. By the obtained results from experiments on the sandwich composite T-joints, reliable technical information about the fracture behavior of this type of joint is provided. The achieved results prepare not only new data for the designers, but can also be used for future computational models of adhesively bonded composite T-joints. The outcomes of the experiments at high rate of loading on UHPC material, presents data regarding to response of this material to dynamic loading regime. The data extracted from the experiments can speed up the robust design and it is beneficial for future material developments and load carrying capabilities of this cementitious composite materials.Source Type:Doctoral Thesis1 7 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , Fracture behavior of double edge notch AlSi10Mg alloy fabricated by laser powder bed fusionIn the present study, the fracture behavior of additively manufactured (AM) metal parts has been investigated. To this aim, double edge notch tension (DENT) specimens have been printed using AlSi10Mg alloy based on the laser powder bed fusion (PBF) technique. Particularly, DENT specimens have been fabricated with three different ligament lengths and three different printing directions for each ligament length. In this study, we used the concept of essential work of fracture to describe the fracture behavior AMed parts. According to a series of tests under static loading conditions, influences of the ligament length and printing direction on the structural integrity of the DENT specimens have been determined. According to the experimental practices, levels of ductility and size of plastic zone in the ligament region have been documented. Here, we utilized digital image correlation technique to measure strain fields on the surface of the examined samples. Moreover, numerical simulations have been conducted to simulate the stress distribution from DENT specimens. In addition, visual inspection of the fracture surfaces has been conducted using a free-angle observation system. The outcome of this study can be used for future designs of PBF printed parts with a better structural performance.Source Type:Article3 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , 2 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Machine learning in predicting mechanical behavior of additively manufactured partsAlthough applications of additive manufacturing (AM) have been significantly increased in recent years, its broad application in several industries is still under progress. AM also known as three-dimensional (3D) printing is layer by layer manufacturing process which can be used for fabrication of geometrically complex customized functional end-use products. Since AM processing parameters have significant effects on the performance of the printed parts, it is necessary to tune these parameters which is a difficult task. Today, different artificial intelligence techniques have been utilized to optimize AM parameters and predict mechanical behavior of 3D-printed components. In the present study, applications of machine learning (ML) in prediction of structural performance and fracture of additively manufactured components has been presented. This study first outlines an overview of ML and then summarizes its applications in AM. The main part of this review, focuses on applications of ML in prediction of mechanical behavior and fracture of 3Dprinted parts. To this aim, previous research works which investigated application of ML in characterization of polymeric and metallic 3D-printed parts have been reviewed and discussed. Moreover, the review and analysis indicate limitations, challenges, and perspectives for industrial applications of ML in the field of AM. Considering advantages of ML increase in applications of ML in optimization of 3D printing parameters, prediction of mechanical performance, and evaluation of 3D-printed products is expected.Source Type:Article2 13 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Open Access , Mixed mode brittle fracture of stereolithographic 3D-printed partsTechnical advances in additive manufacturing (AM), also known as three-dimensional (3D) printing, have led to applications of this technology in creation of end-use items. Consequently, performance and the mechanical strength of AMed parts have become of significant importance. In this research, fracture behavior and crack propagation of AMed cracked plates are investigated. To this aim, the stereolithography (SLA) technique is used to fabricate square plate specimens with a hole in the center and radial cracks that started at the perimeter of the central hole. Here, full range of mixed-mode fracture (from pure mode I to pure mode II) are obtained by altering the angle between the crack and the applied load. We used the finite element method to determine stress intensity factors. This study deals with a series of experiments on 3D-printed cracked plates to study mixed-mode fracture and crack propagation in brittle fracture of SLA 3D-printed components. Additionally, the digital image correlation technique was used to determine strain field on the surface of the specimens. As SLA is one of the most commonly used concepts in polymer 3D printing and has garnered significant attention for fabrication of complex structural elements, the outcomes of this study are useful for next developments and innovative designs of 3D-printed polymeric components.Source Type:Article326 174 - Some of the metrics are blocked by yourconsent settings
Publication Access status: Metadata only , On the Pin-Bearing Strength of Additively Manufactured Polymer PartsDue to the wide scope of applications of additive manufacturing (AM) in making final products, the mechanical strength of AM parts has become very important. Therefore, different tests are being developed to determine the structural integrity of three-dimensional printed components. In this respect, the pin-bearing test is designed to evaluate the response of a fastener, plate, and hole to stress. In this study, two different polymer materials were used to fabricate the samples utilizing the fused deposition modeling technique. Since the specimen width and hole diameter have effects on the pin-bearing strength and structural integrity of the parts, we prepared the specimens with four hole diameters to determine the influence of this ratio. A series of tensile tests were performed, and the stiffness and pin-bearing strength of additively manufactured specimens were determined. The preferred bearing failure mode was observed in several tested specimens. Subsequently, a scanning electron microscope investigation was conducted on the damaged area of the examined specimens to obtain insights into the damage mechanisms and failure behavior of the aforementioned specimens. We used digital image correlation technique to determine the strain field of dumbbell-shaped test coupons. The results of this research can be utilized for new designs of AM parts with a higher mechanical strength.Source Type:Article2
